Wood finishes compared: polyurethane, oil, lacquer, shellac and wax
A stain gives the wood its color. The finish on top is what decides whether the table survives a hot mug, whether the floor can be fixed where the dog scratched it, and whether that white paint goes yellow by spring. Most of the confusion on the shelf is between products that look interchangeable and are not: Polycrylic and polyurethane, tung oil and the "tung oil finish" that contains none, spar urethane and the interior poly beside it, teak oil that has never met a teak tree.
Every finish here is written up from its maker's data sheet: dry time, recoat window, full cure, coats needed, how much it ambers, how it is cleaned up and how hard the cured film is. The pair pages put two of them side by side in one table and give a straight verdict on which to buy for what. Film finishes (polyurethane, lacquer, shellac, varnish) sit on the surface and take wear best. Penetrating oils and hardwax oils live in the wood, look and feel like bare timber and are repaired with a rag. Stains and deck finishes get the same treatment because the oil versus water-based question comes up on every one of them.
Times assume 70 F and moderate humidity and are typical of the brands named; a cold garage or a thick coat can double any of them. The can wins over this page.
Head-to-head comparisons
- Polyurethane vs Polycrylic
- Tung Oil vs Linseed Oil
- Water-Based vs Oil-Based Polyurethane
- Oil-Based vs Water-Based Stain
- Lacquer vs Polyurethane
- Spar Urethane vs Polyurethane
- Danish Oil vs Tung Oil
- Deck Stain vs Paint
- Polyurethane vs Varnish
- Shellac vs Polyurethane
- Semi-Transparent vs Solid Stain
- Teak Oil vs Tung Oil
- Gel Stain vs Regular Stain
- Transparent vs Semi-Transparent Stain
- Solid Stain vs Paint
- Oil vs Water-Based Deck Stain
- Hardwax Oil vs Polyurethane
- Osmo vs Rubio Monocoat
- Wax vs Polyurethane
Every finish at a glance
| Finish | Type | Dry to touch | Hardness | Water | Color change |
|---|---|---|---|---|---|
| Oil-based polyurethane | Film-building clear coat | 4 to 6 hours | ●●●●● 5/5 | ●●●●● 5/5 | Strong: warm amber from the first coat, keeps deepening for years |
| Water-based polyurethane | Film-building clear coat | 30 minutes to 1 hour | ●●●●○ 4/5 | ●●●●○ 4/5 | None to slight: stays clear, oil-modified versions warm a little |
| Polycrylic | Film-building clear coat | 30 minutes | ●●●○○ 3/5 | ●●●○○ 3/5 | None: water-clear, can look milky if laid on thick over dark paint |
| Spar urethane | Film-building clear coat | 4 to 6 hours oil-based, 1 hour water-based | ●●●●○ 4/5 | ●●●●● 5/5 | Strong for oil-based, slight for water-based |
| Lacquer | Film-building clear coat | 15 to 30 minutes | ●●●○○ 3/5 | ●●●○○ 3/5 | Slight, warms with age; water-white CAB-acrylic versions stay clear |
| Shellac | Film-building clear coat | 15 to 30 minutes | ●●○○○ 2/5 | ●●○○○ 2/5 | Clear/blonde: slight. Amber/orange: strong honey-orange |
| Varnish | Film-building clear coat | 6 to 24 hours | ●●●●○ 4/5 | ●●●●● 5/5 | Strong, the classic honey-gold boat brightwork look |
| Tung oil | Penetrating oil | 24 to 72 hours per coat (faster thinned 1:1) | ●●○○○ 2/5 | ●●●○○ 3/5 | Slight warm honey tone that barely changes over time |
| Boiled linseed oil | Penetrating oil | 24 to 48 hours per coat | ●○○○○ 1/5 | ●●○○○ 2/5 | Strong: yellows on day one and keeps yellowing |
| Danish oil | Penetrating oil | About 6 hours | ●●●○○ 3/5 | ●●●○○ 3/5 | Moderate natural warmth, plus tinted versions (Dark Walnut, Golden Oak, Cherry) |
| Teak oil | Penetrating oil | 8 to 10 hours | ●●○○○ 2/5 | ●●●○○ 3/5 | Moderate warm golden tone |
| Hardwax oil | Hardwax oil | 8 to 10 hours (Osmo) to 24 to 36 hours (Rubio) | ●●●●○ 4/5 | ●●●●○ 4/5 | Slight natural warmth; raw and pure versions keep the wood near-untouched |
| Osmo Polyx-Oil | Hardwax oil | 8 to 10 hours per coat | ●●●●○ 4/5 | ●●●●○ 4/5 | Slight warm tone; Raw 3044 adds white pigment to cancel it |
| Rubio Monocoat Oil Plus 2C | Hardwax oil | 24 to 36 hours | ●●●●○ 4/5 | ●●●●○ 4/5 | None in Pure; every other shade is a built-in color |
| Paste wax | Wax | 10 to 15 minutes, then buff | ●○○○○ 1/5 | ●○○○○ 1/5 | Natural: none. Dark wax tints toward brown |
| Oil-based stain | Interior wood stain | - | - | - | |
| Water-based stain | Interior wood stain | - | - | - | |
| Gel stain | Interior wood stain | - | - | - | |
| Transparent deck stain | Exterior deck finish | - | ●●●○○ 3/5 | - | |
| Semi-transparent deck stain | Exterior deck finish | - | ●●●●○ 4/5 | - | |
| Solid deck stain | Exterior deck finish | - | ●●●●○ 4/5 | - | |
| Exterior paint | Exterior paint | - | ●●●●○ 4/5 | - | |
| Oil-based deck stain | Exterior deck finish | 24 to 48 hours before foot traffic | - | ●●●●○ 4/5 | - |
| Water-based deck stain | Exterior deck finish | 2 to 4 hours to touch, 24 to 48 hours to foot traffic | - | ●●●●○ 4/5 | - |
Film-building clear coats
Oil-based polyurethane
Oil-based polyurethane is the default clear coat at every hardware store for a reason: it builds a hard, water-resistant film in two or three coats and shrugs off the abuse a tabletop or a floor takes. The trade-offs are the smell, the slow recoat window and the color. It goes on with an amber cast and keeps warming for years, which flatters oak and walnut and turns white paint or pale maple yellow.
Typical products: Minwax Fast-Drying Polyurethane, Varathane Ultimate Oil-Based Polyurethane
Water-based polyurethane
Water-based polyurethane dries in an hour, cleans up with water and stays clear, so pale woods and painted pieces keep the color you chose. Modern versions (Varathane Ultimate, General Finishes High Performance) are hard enough for floors. It needs an extra coat to match the build of oil poly, dislikes being overbrushed, and the first coat will raise the grain a little, so plan a light sanding after it.
Typical products: Varathane Ultimate Water-Based, Minwax Water Based Polyurethane, General Finishes High Performance
Polycrylic
Polycrylic is Minwax’s water-based acrylic clear coat and the one most people grab for painted furniture, crafts and light-duty shelving. It dries in half an hour, has almost no smell and does not yellow. It is also softer than either kind of polyurethane and will mark under hot mugs or a dragged chair, so Minwax itself steers you away from floors and tabletops.
Typical products: Minwax Polycrylic, brush-on and aerosol
Spar urethane
Spar urethane is polyurethane tuned for outdoors: more oil in the mix so the film flexes as wood swells and shrinks, plus UV absorbers that slow the sun from chalking and cracking it. The same softness that lets it flex means it scratches more easily than interior poly, so it is the wrong choice for an indoor table and the right one for a front door, outdoor furniture or a boat interior.
Typical products: Minwax Helmsman Spar Urethane, Varathane Spar Urethane, Cabot Spar Varnish
Lacquer
Lacquer is the finish on most factory furniture and guitars because it sprays beautifully, dries in minutes and every new coat melts into the last one, which makes repairs almost invisible. The solvent is harsh and flammable, so it belongs in a sprayed booth or a well-ventilated garage. Nitrocellulose lacquer warms slightly with age; CAB-acrylic and pre-catalyzed versions stay water-white and harder.
Typical products: Deft Clear Wood Finish, Minwax Clear Brushing Lacquer, Watco Lacquer, aerosol spray lacquer
Shellac
Shellac is a natural resin dissolved in alcohol. It dries in minutes, sticks to almost anything and is the classic sealer under other finishes and over knots and pet stains. As a topcoat it has real limits: water and alcohol leave white rings, and it is soft. Dewaxed shellac (Zinsser SealCoat) is the one to use under polyurethane; the waxy kind stops poly from bonding.
Typical products: Zinsser Bulls Eye Shellac (clear and amber), Zinsser SealCoat (dewaxed), flakes mixed at home
Varnish
Traditional varnish is oil plus resin cooked together, the finish on wooden boats and old doors. It flows out to a deep gloss, flexes with the wood and takes sun better than interior polyurethane, but it needs six to eight thin coats, a day between each, and a maintenance coat every year or two outdoors. Polyurethane is technically a varnish too; the difference is the resin and how fast it cures.
Typical products: Epifanes Clear Varnish, McCloskey Man O' War, Pettit Captain's, Interlux Schooner
Penetrating oils
Tung oil
Pure tung oil is pressed from the nut of the tung tree and cures into a soft, matte, water-resistant finish that lives in the wood rather than on it. It takes a week of coats and a month to cure, but it never peels, it does not yellow the way linseed oil does, and a worn spot is fixed with a rag. Watch the label: Minwax and Formby’s “Tung Oil Finish” is a thinned varnish with little or no tung oil in it.
Typical products: Hope's 100% Tung Oil, Real Milk Paint Pure Tung Oil, Sutherland Welles
Boiled linseed oil
Boiled linseed oil is the cheapest wood finish on the shelf and the oldest. It soaks in, hardens slowly, and leaves a dull, hand-rubbed look with almost no protection against water or wear. It yellows quickly and keeps going. The “boiled” is marketing: the oil has metallic driers added so it cures in days instead of weeks. Oily rags can ignite on their own, so lay them flat outside to dry.
Typical products: Sunnyside Boiled Linseed Oil, Klean-Strip, Tried & True (raw, no driers)
Danish oil
Danish oil is a thinned blend of oil and varnish, so it behaves like an oil to apply (flood, wait, wipe) but cures a bit harder and faster than a pure oil. It gives a low-sheen, in-the-wood look in one afternoon and comes pre-tinted in walnut, cherry and oak shades. Watco warns to wait 72 hours before topcoating it with polyurethane, and the rags carry the same self-ignition risk as any oil.
Typical products: Watco Danish Oil, Rust-Oleum Danish Oil, Tried & True Danish Oil
Teak oil
Teak oil contains no teak. It is a thin oil and resin blend, usually with UV inhibitors, formulated to soak into dense, oily woods like teak, mahogany and ipe that reject thicker finishes. Outdoors it looks good for a season and needs re-oiling two or three times a year. Indoors it behaves like Danish oil. Skip it on pine or oak; a Danish oil does the same job cheaper.
Typical products: Watco Teak Oil, Star brite Premium Golden Teak Oil, Minwax Teak Oil
Hardwax oils
Hardwax oil
Hardwax oils are the finish behind most matte Scandinavian-looking floors and tables. A blend of plant oils and hard waxes soaks into the top of the wood and cures there, so there is no film to scratch through or peel, and a worn patch can be re-oiled without redoing the whole surface. Coverage is huge because the coats are so thin, which is how a small, expensive can works out cheaper than it looks.
Typical products: Osmo Polyx-Oil, Rubio Monocoat Oil Plus 2C, Fiddes Hard Wax Oil, Odie's Oil
Osmo Polyx-Oil
Osmo Polyx-Oil is the German hardwax oil that most flooring contractors reach for. Two thin coats, eight to ten hours apart, give a surface that resists water and wine, feels like bare wood and can be spot-repaired. It is forgiving to apply as long as the coats are genuinely thin; a thick coat stays tacky for days. The Raw version adds a trace of white to stop the warm cast a clear oil gives pale woods.
Typical products: Osmo Polyx-Oil Original 3032 satin, 3062 matte, 3011 gloss, Raw 3044
Rubio Monocoat Oil Plus 2C
Rubio Monocoat is a Belgian two-part hardwax oil that bonds to the wood fibers in a single coat: spread, wait a few minutes, buff every trace off. Because there is no second coat, the whole job is one day and the color line of fifty-plus shades (including white and gray washes) is built into the oil. It is the most expensive finish per can on this page and about the cheapest per square foot.
Typical products: Rubio Monocoat Oil Plus 2C in Pure plus 50-odd colors; Rubio Hybrid Wood Protector outdoors
Waxs
Paste wax
Paste wax is a polish, not a protective finish. On bare wood it gives a soft glow and a slick feel that lasts until the next spill; on top of a cured finish it adds a little shine and hides fine scratches. Its real place is over chalk paint, milk paint and oil finishes where the look matters more than durability. Once wax is on, nothing else will stick until it is stripped with mineral spirits.
Typical products: Minwax Paste Finishing Wax, Briwax, Howard Citrus Shield, Annie Sloan Soft Wax
Interior wood stains
Oil-based stain
Oil-based stain is what most people mean by “wood stain”: Minwax Wood Finish, Varathane Premium. It soaks deep, gives you ten minutes to wipe it evenly and produces the classic warm browns. The downside is on soft or tight-grained woods (pine, maple, birch, cherry) where it blotches unless you pre-treat with wood conditioner, and the eight-hour wait before a topcoat.
Typical products: Minwax Wood Finish, Varathane Premium Fast Dry, Old Masters Penetrating Stain
Water-based stain
Water-based stain dries in an hour, cleans up with water and comes in far more colors, including whites, grays and bright tints that oil stains cannot do. It blotches less than oil on soft woods but raises the grain, so the standard move is to wet the wood, let it dry and sand lightly before staining. It penetrates less deeply, so the color sits closer to the surface and sands through faster.
Typical products: Minwax Water Based Wood Stain, Varathane Water-Based Stain, General Finishes Water Based Stain
Gel stain
Gel stain is a thick, pudding-like stain that sits on the surface instead of soaking in. That is exactly why it works on blotch-prone pine and maple, on veneers and plywood edges, and on fiberglass and metal doors that would reject a liquid stain. The price is a slightly muted grain and a long dry time before topcoating. General Finishes Java is the gel stain behind most dark cabinet makeovers.
Typical products: General Finishes Gel Stain, Minwax Gel Stain, Old Masters Gel Stain
Exterior deck finishs
Transparent deck stain
A transparent deck stain is really a water repellent with little or no pigment. It makes the wood look wet and rich on day one and does almost nothing to stop the sun from graying it, so expect to recoat every year. It is the right pick for a brand-new cedar or redwood deck whose color you want to keep for a season, and the wrong pick for anything you would rather not touch again for three years.
Typical products: Thompson's WaterSeal Clear, Cabot Australian Timber Oil Natural, Ready Seal Natural Cedar
Semi-transparent deck stain
Semi-transparent is the middle of the deck-stain range and the one most people should buy. Enough pigment to block a good share of UV and give a real color (cedar, redwood, walnut), still thin enough that the grain shows through. Penetrating oil versions wear away cleanly and recoat without stripping; the water-based ones last a bit longer but can flake where they have built up.
Typical products: Ready Seal, Cabot Semi-Transparent, Behr Premium Semi-Transparent, Olympic Elite
Solid deck stain
Solid deck stain is a thin opaque paint that soaks a little into the wood and hides it completely. It blocks UV better than anything else, covers mismatched or weathered boards, and lasts three to five years on a floor. Because it is a film, water that gets under it (end grain, cracks, shaded boards) will lift it, and once a deck has been solid-stained you cannot go back to a transparent look without sanding it off.
Typical products: Behr Premium Solid Color Stain, Cabot Solid Color, Sherwin-Williams SuperDeck Solid, Olympic Maximum Solid
Oil-based deck stain
Oil-based deck stains penetrate rather than coat, so they fade and wear away instead of peeling, and a recoat is a wash and a fresh coat with no scraping. They take a day or two to dry, smell, and in shaded damp spots the oil itself can feed mildew unless the formula carries a good mildewcide. Several states restrict their VOCs, which is why the oil-based products on a California shelf are not the ones in Texas.
Typical products: Ready Seal, Cabot Australian Timber Oil, Penofin, Armstrong Clark, TWP
Water-based deck stain
Water-based deck stains dry in hours, keep their color longer and resist mildew better than most oils, and they are the only option where VOC rules bite. They form a thin film, so they can flake at the surface if applied over a dirty or still-damp deck, and that film has to be sanded or scraped where it has lifted before the next coat. Hybrid alkyd-acrylic versions split the difference.
Typical products: Defy Extreme, Behr Premium (water-based), Olympic Elite, Sherwin-Williams SuperDeck
Exterior paints
Exterior paint
Paint is the thickest film you can put on a deck and the one most likely to peel there. On vertical surfaces (siding, railings, trim) it lasts longer than any stain; on a horizontal deck that holds snow and puddles, moisture in the boards pushes the paint off in sheets within a few years. Porch and floor enamels are tougher than wall paint and are the only paints worth considering on a walked-on surface.
Typical products: Behr Porch & Patio Floor Paint, KILZ Porch & Patio, Sherwin-Williams Porch & Floor Enamel
Frequently asked questions
What is the most durable clear finish for wood?
For an interior floor or tabletop, oil-based polyurethane, with a quality water-based polyurethane close behind. Outdoors, spar urethane or a traditional varnish, because both flex and carry UV blockers. Nothing beats a film finish for wear; oils and waxes trade protection for easy repair.
Which wood finish does not yellow?
Water-based polyurethane, Polycrylic, CAB-acrylic lacquer and most hardwax oils stay close to clear. Oil-based polyurethane, varnish, boiled linseed oil and Danish oil all amber on day one and keep warming for years, which looks right on oak and walnut and wrong on white paint or maple.
What finish is food safe for a cutting board?
Pure tung oil or a mineral oil and beeswax blend, both fully cured. Most cured film finishes are inert, but makers do not rate them for food contact and a chipped film ends up in the food. Boiled linseed oil has metallic driers and is not sold for food use.
Can I put polyurethane over an oil finish?
Over a fully cured Danish oil or tung oil, yes, usually after 72 hours or more. Over paste wax, no: wax stops anything from bonding and has to be stripped with mineral spirits first. Over a hardwax oil, also no, the oil is the finish.
Oil-based or water-based stain, which is better?
Oil-based soaks deeper, gives longer working time and the classic warm browns; water-based dries in an hour, blotches less on pine and maple and comes in grays, whites and bright colors oil cannot do. Either takes a clear topcoat; a water-based poly over oil stain needs the stain fully dry first.
Should I stain or paint a deck?
Stain, almost always. Paint sits on top and peels on a horizontal surface that holds water and snow. A solid deck stain hides the wood as well as paint does and lasts three to five years on a floor; semi-transparent shows the grain and recoats without scraping.